A couple of posts back, I showed you another of the suitcase dressers that I had completed. I had a comment or two from readers that said they really liked the concept but could find no instructions or tips or any other helpful information on how to recreate the look. Well, I have been working on a short console type cabinet for a client that I decided that I would do a tutorial on how to make the suitcase dresser, or at least, how I do it.
Okay, I have done this about four times (and I have another under way). The particular pieces of furniture that I chose are those sound in structure, but devoid of any real character. Like this dresser.
I took the drawers out and removed their hardware. This left this odd bumpy pieces that under closer inspection appeared to be attached to the fronts. A little prying and they came right off. They were attached with three very long staples and made of pressed wood. Basically useless.
I discarded those pieces.
You can see the long one leaning against the front of the drawer.
So here are the drawers with clean fronts ready to be worked on.
Oh, and speaking of ‘clean’, it is always a good idea to wipe down everything with a clean cloth avoiding chemical cleaners. You don’t want anything interfering with the bonding of glue and drawer front. Wipe out the interiors of the drawers and the inside of the cabinet. Nice to have everything clean to start with.
Next, I made a couple of trips to my local hangouts; Joann’s and then Home Depot. First I chose fabric. I knew the piece was to be primarily black (cabinet is the ‘usual’ Deep Space black in semi-gloss from Behr). I painted the cabinet and set it aside. I would have to do two coats to get a nice even coverage. Below, you will see the two fabrics I chose. I purchased the width of the drawer plus 4 inches, enough to wrap around the top and bottom edges. This will make sense when we get further.
The type of fabric used is as least considered an upholstery fabric. I like to use styles and colors that mimic what I think of when it comes to older suitcases, something around the 50’s and 60’s. I collected these images to give you a place to start. Let you imagination take you wherever you want to go, who is to say what is or isn’t suitcase fabric? Also, remember you can always use just about any colored vinyl. Let’s you really get a pop of color in there.
Here you can get an idea of the weight of fabric, it does need to be a heavier type fabric. Working with a heavier and more stable fabric is easier and it will wear longer. Not all upholstery or furniture fabric will work, you have to be careful of glue saturation. More on that later.
Here are several examples of fabrics that I have purchased to use in upcoming projects. You can see the wide selection of colors and patterns.
Next I cut off the selvage. I am also a quilter, so I use the cutting mat and rotary cutting tool and straight edge tool that I already own. You could just as easily use a scissors to cut off the edge.
Now measure the length of the drawer adding four inches. Now cut the length.
Now fold the fabric onto itself into about thirds. What you are doing here is to make a crease in the fabric to replicate the lid meeting the body of the suitcase.
Pin to hold the fold. You may want to pull the fabric back and look (at the right sides together) to make sure that your fold placement looks good. For me, it was trial and error the first couple of times. For the most part, I figure as long as striped or obvious patterns look right and match appropriately.
Sew about a 1/4″ seam. This doesn’t have to be perfect measurement, again, as a quilter, this is what I normally sew. And I don’t lose too much of the fabric to the seam.
Now open the seam and press. Sometimes, when the fabric is really heavy, pressing helps to maintain a nice flat surface when you apply the fabric to the drawer front.
Now apply a liberal amount of glue mixture to the drawer front. I use a combination of about 4 parts white glue (good ‘ol Elmers, I buy it by the gallon size) and 1 part water. This makes it just a little easier to work with. Now working with the fold towards the bottom, place the fabric evenly on the drawer front folded… then unfold when the line is straight. Believe me, when you are all done and that seam is crooked, it will jump out at you and you will see it every time you look in its direction!
Now unfold and smooth the remainder of the fabric. Start at the center and work out to ensure a smooth coverage. Be careful not to pull when you smooth and move the fabric.
In most cases, I use those big office binder clips, to hold the fabric as it dries. You will only be doing the two long edges now.
Two things you need to be aware of if you leave the clips on too long … one, these clips can possibly leave rust if the fabric is saturated with the glue mixture. Two, you can get a crease line when the glue dries where the binder meets the fabric. These can be avoided if you leave the clips on long enough to allow the glue to ‘set’ but before it dries. Again, this is just a matter of trial and error.
Occassionally, if there is not enough ‘lip’ on the drawer to support the use of a binder clip, I will use a stapler. Just a regular stapler, not a heavy duty one. This is just to hold the fabric in place until it dries enough to remove the support.
Another view of the fabric drying:
Once the fabric has dried enough to maintain the connection to the drawer, remove the binder clips. To use these on a multi-drawer dresser, you will need quite a few of them. Allow the glue to dry at least overnight, better if you can give it the full twenty-four hours recommended.
This will be where you will see if your choice of fabric was good. I didn’t plan this, but it ended up working out okay since I am doing a tutorial. After all, a good tutorial will also tell you what not to do as well as what to do.
In this case, this fabric wasn’t a good choice after all. The glue soaked into the fabric to the point that when it dried, it discolored the fabric. It is pretty difficult to see in the photos, but where the glue was too thick, it discolored the fabric.
I was able to pull the fabric off without any damage to the drawer front. Off to the store for a replacement fabric, this time I dropped by Hobby Lobby to check out their selection. I found a beautiful black and shades of silver/gray with circles to replace it. Back through the steps to get the second drawer caught up to the first.
Once the long edges of the drawer have been dried, you need to repeat the process to the ends. This is usually much easier since they are shorter in length. Again, another 24 hours is recommended to allow the glue mixture to dry.
Now, you need to trim the excess from the drawers. This process is dependent on the specific shape of the drawers and how they fit into the cabinet. I usually chose drawers that lay on top of the cabinet as opposed to being recessed. Perhaps this photo will help clarify what I am talking about:
Drawer styles vary, but again, I like to stick to drawer styles that are similar. I trim the fabric under the drawer first, using a sharp razor blade to remove it where the drawer front meets the drawer. Using the inside corner as a guide, pull the blade along to cut the fabric. Trim the edges using the razor blade or a small pair of scissors.
Pull the fabric away as you move down the drawer. This helps to see where you might need to re-cut; remember, this is heavy duty fabric!
Once you have the fabric removed, apply more glue to the edges, trimming away errant threads as you go. Be liberal in your glue application, you want the edges to stick well!
Another waiting period for glue to dry. Then it is time to install hardware.
First, let me talk a little about hardware. I think it looks better to have a variety of styles and colors. Otherwise, you are back to looking like it is just another dresser. I keep my eyes open in many places I shop for possible candidates. One place I love to browse through bins is Habitat for Humanity’s ReStore. They have some awesome old and unique pieces. Often dirty and without mates or pairs, but all the better. And usually either 50 cents or a buck!
I always peruse the hardware aisles at Home Depot, Lowe’s and Ace Hardware, but you can also look at places like Michael’s, Joann’s and Hobby Lobby. Occasionally, I will find good stuff at the dollar stores and thrift stores. I browse eBay and Craiglist too. Because I know I will be doing these from time to time, I like to keep an eye open all the time and in the end, this gives me a good selection to choose from.
Here is are some examples of what Home Depot has to offer:
Position on the drawer front to suit yourself and attach. On one drawer front, I used a piece of a leather belt (picked up at Goodwill for $1.98) and two pipe straps to simulate a leather suitcase handle.
Next, as clasps for the case I used silver window sash hardware one on each side, about 5″ from the edges:
The other drawer was treated with a black gate handle, nice and solid:
And it also received the window sash hardware, this time in black. Also, to vary the hardware location, I mounted these about 4″ from the edge. Just to keep from getting to repetitive and keep things looking different.
Insert the drawers into the cabinet, take a step back and let out a long overdue and well deserved sigh. You should be done at this point. A few more photos of the completed project. First, a close-up of the hardware, you can see that things don’t line up and that is on purpose.
A step back to view the whole thing, cabinet included:
Whew! About two thousand words and pictures! pictures! pictures! I hope this all makes sense, but if you have questions, please ask! Like I said, I have done this four or five times now and I may have taken a short cut or two without realizing it. Once you do something a few times, you kind of know where you can cut corners but is information that would be helpful when trying to show someone else how to do it.
Oh, just for fun, here are the other dressers that I have done, the first one even had a small matching nightstand:
and the very first effort:
This one shows you a before and after shot:
Okay! I will say goodnight! I loved doing this tutorial but had no idea that it would take nearly 5 hours to write. Glad I was taking photos along the way.
Thank you for dropping by! Come back again!
And keep crafting y’all!